Ultimaker: Difference between revisions

Jump to navigation Jump to search

Ultimaker (view source)

Revision as of 02:40, 1 July 2020

665 bytes removed ,  1 July 2020
Retired Printer
(Retired Printer)
 
(8 intermediate revisions by 3 users not shown)
Line 12: Line 12:


!Status
!Status
|Operational
| Broken - Retired
|Non-functional
| Broken - Retired
|-
|-


!Material
!Material
|Orange PLA
|ABS only
2.93mm,
|3mm PLA only
Packing Factor: 1
|-
Temp: 225degC
 
|N/A
!Performance State
|Hardware: works well
Software: OctoPrint works well
|Hardware: works well
Software: OctoPrint works well
|-
 
!Pending tasks
|
|
|-
 
|}
|}


==Material Feedstock==
==Material Feedstock==
Our current preferred supplier of good PLA is Montreal based [http://voxelfactory.com/ Voxelfactory], their PLA is reasonably priced and ships fast.
<strike>Our current preferred supplier of good PLA is Montreal based [http://voxelfactory.com/ Voxelfactory], their PLA is reasonably priced and ships fast.</strike>
 
Had some issues with brittle filament from Voxelfactory.
 
Norm recommended [http://www.repraper.com/ repraper.com].
 
Rob found a Toronto wholesaler [http://www.dynamishobbies.com/ DynamisHobbies.com] who left a sample spool of 1.75mm at the lab.


All PLA is hygroscopic (water absorbing) and exposure to moisture over time degrades the material. We have a (mostly) airtight latching storage bin with desiccant (CaCl[sub]2[/sub]) to reduce moisture internally. Store PLA inside this bin, keep it closed and open it only when needed.
All PLA is hygroscopic (water absorbing) and exposure to moisture over time degrades the material. We have a (mostly) airtight latching storage bin with desiccant (CaCl{{sub|2}}) to reduce moisture internally. Store PLA inside this bin, keep it closed and open it only when needed.


NB: ABS and other mystery inventory is stored in this bin as well!
NB: ABS and other mystery inventory is stored in this bin as well!
Line 38: Line 55:
|-
|-


|Purple 3mm
|White, 1.75mm
|2.916mm, Packing Density = 0.6
|1.75mm
|Full spool, Norm's personal stock
|Partially used, DynamisHobbies sample.
|-
|-


|Orange 3mm
|White, 1.75mm
|2.934mm
|1.65mm
|Partial spool. Density = 1.135g/cm^3
|Couple meters left. Came with the Type A
|-
|-


|Black 3mm
|Green, 1.75mm
|2.899mm
|
|Partial spool.
|
|-
|-


|White 3mm
|Yellow, 3mm
|2.88mm, Packing Density = 0.5, T=230degC
|2.90mm, Packing Density = 0.6
|Requires special settings to print. Density = 1.149g/cm^3
|Partially used.
|-
|-


|Green 3mm
|Black, 3mm
|2.79mm
|
|Full spool
|Partially used.
|-
 
|White 3mm
|2.78mm
|Full spool, unopened. Norm's personal stock
|-
|-


|Glow in the dark blue, 3mm
|Glow in the dark blue, 3mm
|2.983mm
|2.983mm
|Full spool, unopened. Norm's personal stock
|Partially used.
|-
|-


|Yellow, 3mm
|Blue, 3mm
|2.90mm, Packing Density = 0.6
|2.95mm
|Full spool, unopened. Norm's personal stock
|Partially used.
|-
|-


|}
|Orange, 3mm
 
|
==Components/Upgrades==
|Unopened.
{| cellpadding="5" cellspacing="0" border="1"
!
!Ultimaker #1
!Ultimaker #2
|-
|-
!Extruder
|Standard, upgrade needed (one day)
|New Extruder, Boden Tube, and v2 Hot end required
|-
!XY Blocks
|Standard
|Repaired, installed
|-
!Bearing Endcaps
|Upgraded
|To be installed
|-
!Motor Mounts
|Standard
|To be installed
|-
!Motor Tensioners
|Pending
|To be installed
|-
!Spool Holder
|Upgraded
|To be installed
|-
!Belt tensioners
|Installed
|To be installed
|-
!Fan Cowling
|Upgraded, new one to be printed and installed eventually
|To be installed
|-
!Z Home Switch Adjuster
|Upgraded but problematic
|Upgraded
|-
!Print bed
|Standard
|Upgrade in progress
|-
!Raspberry Pi
|Separate
|To be acquired, bracket for mounting to be printed
|-
!Motor cooling
|None
|To be installed
|-
!Vibration isolators
|None
|To be installed
|-


|}
|}
Revident
150

edits

Retrieved from "https://knowledge.hacklab.to/wiki/Special:MobileDiff/66...1866"

Navigation menu