3D Printers/FlashForge Creator Pro: Difference between revisions

Jump to navigation Jump to search
→‎Status: update Octoprint url
(→‎Status: update Octoprint url)
(41 intermediate revisions by 3 users not shown)
Line 5: Line 5:
* '''Working'''
* '''Working'''
* [[FlashForge_Creator_Pro#Usage|Slic3r Settings here]]
* [[FlashForge_Creator_Pro#Usage|Slic3r Settings here]]
* '''http://octopi4.hacklab.to/'''
* '''http://octopi4.in.hacklab.to/'''
* [[FlashForge_Creator_Pro#SD Card|Or print without OctoPrint using the SD Card]]
* [[FlashForge_Creator_Pro#SD Card|Or print without OctoPrint using the SD Card]]
</onlyinclude>
</onlyinclude>


*Last Known Good Settings: White solutech PLA - First layer: 220 deg, Rest of layers: 210 deg. No heated bed. Extrusion multiplier 1, but it seems to be over extruding just a little, can try .975
-----
Last Known Good Settings
{| cellpadding="5" cellspacing="0" border="1"
!Date
!Filament type, colour, brand
!First layer
!Other layers
!Notes
|-
 
| Nov, 2018
| Hatchbox forest green ABS
| Nozzle: 240, Bed: 110
| Nozzle: 240, Bed: 110
| DO NOT use enclosed chamber. Weird, I know. Put a fan on it after the 1st layer. 1st layer may be wavy, you may have to slow down the 1st layer speed to like 15-20 mm/s, or perhaps maybe the bed's too hot?? **biting nails emoji**
Thanks to Zach for suggesting not to use an enclosed chamber, it was driving me flipping insane......  (╯⊙﹏⊙)╯︵ ┴─┴
|-
 
| Nov, 2018
| AMZ3D Black, ABS
| Nozzle: 235, Bed: 110
| Nozzle: 230, Bed: 110
| Use enclosed chamber. Works decently but these settings are still not tweaked precisely, may over-extrude. Try lowering the temp by 5 C, or set extrusion to 0.95.
|-
 
| Aug 10, 2018
| 3D Solutech PLA, white
| Nozzle: 215, Bed: off
| Nozzle: 205, Bed: off
| Extrusion multiplier at 0.925. Put fans on it!
|-
 
|}


== Features ==
== Features ==
Line 18: Line 50:
* Dual extruder
* Dual extruder
* 1.75mm filament
* 1.75mm filament
* Absolute max temp: 250 C
* Nozzle max temp: 250 C
* Heated bed
* Heated bed max temp: 120 C
* Removable glass print plate with PEI sheet. Silicone heat transfer sheet to hold it. The stock aluminum build plate (covered in a black substance) is bowed with the middle as the high point.
 
== Glass Print Plate Usage ==
Glass plate is of GO-3D brand, hopefully real mccoy stuff that is flat... It is covered with a PEI sheet that is adhered to the plate with 3M 468MP High Temp Tape. A blue silicone heat transfer sheet keeps the glass in place with friction and fills gaps between the plate and the aluminum bed, it is a type of silicone used for heat sinks for electronics.
 
* NEVER CLAMP glass plate to bed. It will cause warping of the glass plate. Yes glass warps and bends, look it up. The silicone sheet will keep it in place no problem.
*One corner of the print plate is marked 'Front Right' and is blacked in a little around the corner. When facing the printer, this corner goes to corner that is on the right-hand side and is closest to you (duh, but just to be sure...).
*The temperature of the surface of the glass plate will be lower than the aluminum bed, may have to use higher bed temp than on other printers
* PEI sheet is prep-free surface for ABS and PLA, hot or cold. If you have another material, check first to make sure it will work on PEI. If not, then put tape on top of the sheet and then glue/hairspray/whatever.
* Clean PEI sheet with 85% Isopropyl Alcohol and a paper towel, a green spray bottle should be near the printer. Can also use soap and water.
* The flat spatula used to remove objects from the print plate is also useful for removing glass plate from silicone sheet.


== Usage ==
== Usage ==
'''UPDATE:''' See the "'''Cura 3 Settings for this Printer'''" section for how to configure Cura 3.4.1 to use this printer.
Creator Pro uses different toolchain than the rest of the printers in the lab. This printer is based on one of Makerbot printers and Makerbot as a company would rather have you use Windows-only makerbod-approved software.
Creator Pro uses different toolchain than the rest of the printers in the lab. This printer is based on one of Makerbot printers and Makerbot as a company would rather have you use Windows-only makerbod-approved software.


Line 34: Line 80:


== SD Card ==
== SD Card ==
You can print from the printer directly by putting your print file on an SD card, there is one already in the printer. It only accepts x3g files, so you will have to convert your .gcode file (made in slic3r) to x3g using this utility http://markwal.github.io/GpxUi/
You can print from the printer directly by putting your print file on an SD card, there is one already in the printer. It only accepts x3g files, so you will have to convert your .gcode file to x3g using this utility called GpxUi http://markwal.github.io/GpxUi/
 


A copy of GpxUi can be found on the SD card in the printer.
A copy of GpxUi can be found on the SD card in the printer.
Line 43: Line 88:
... '''PRINTER TAB'''<br />
... '''PRINTER TAB'''<br />
'''Printer Settings'''
'''Printer Settings'''
* X (Width): 266 mm
* X (Width): 226 mm
* Y (Depth): 144 mm
* Y (Depth): 144 mm
* Z (Height): 150 mm
* Z (Height): 150 mm
Line 122: Line 167:
See https://github.com/prusa3d/Slic3r-settings
See https://github.com/prusa3d/Slic3r-settings


==Print Settings==
==A few random printing tips==
 
These are general printer settings that work. If filament has different temperature settings, follow filament temperature settings.
 
Smaller prints will better adhere to the bed than larger prints. If the print hasn't failed in the first 10% of the print job, it will be unlikely to fail after that.
 
Use Cubic Infill (Available only in Slic3r prusa edition), as it provides rigidity in all directions [http://www.prusaprinters.org/introducing-slic3r-prusa-edition/] and doesn't make printer resonate.
 
Do not use honeycomb -- as at the speeds of the default settings, it will cause printer to resonate and skip.
 
------
'''Orange (translucent) PLA:'''
 


In Slic3r in Fillament Settings tab, '''Right Extruder''' filament profile and in Print Settings tab, '''Fast''' print profile.
*Smaller prints will better adhere to the bed than larger prints. If the print hasn't failed in the first 10% of the print job, it will be unlikely to fail after that.


First Layer:
*Use Cubic Infill (Available only in Slic3r prusa edition), as it provides rigidity in all directions [http://www.prusaprinters.org/introducing-slic3r-prusa-edition/] and doesn't make printer resonate.
  Filament: 220
  Bed:      70


*Do not use honeycomb -- as at the speeds of the default settings, it will cause printer to resonate and skip.


Other Layers:
*Leaning or drifting prints? Tighten all the belts, especially the Y-axis stepper motor belt. That stepper is prone to becoming loose because the Y-stepper motor puts out more power than the X. A link to a video is in the maintenance section.
  Filament: 210
  Bed:      60


------
*Always store the printer with the X carriage in a corner. (It homes itself to the back left corner anyway when a print is done). But this is to prevent the X and Y axis rods from sagging over time, especially the X axis. It's a known problem, I think, I swear I read it on the internet!
 
------
'''White PLA:'''
 
 
In Slic3r in Fillament Settings tab, '''Right Extruder''' filament profile and in Print Settings tab, '''Fast''' print profile.
 
First Layer:
  Filament: 220
  Bed:      70
 
 
Other Layers:
  Filament: 220
  Bed:      60
 
Print using *105% flow*
------
 
 
'''ABS:'''
 
In Slic3r in Fillament Settings tab, '''ABS Right''' filament profile and in Print Settings tab, '''ABS_first_layer''' print profile. Currently profile is set to 6 skirt layers -- this is normal, ABS needs wide skirt for better adhesion to the bed.
 
 
When printing, you '''absolutely have to''' have a heated chamber, or ABS prints will definitely warp and very likely will not stick to kapton tape.
 
In order to construct heated chamber -- cover the front of printer with a piece of plywood or MDF from the workshop and put some cardboard on top of the printer out of extruder path so the heat escapes more slowly. Pre-heating heaated bed for 5 minutes before starting helps a lot -- set the Bed temperature to 100C in Octopi temperature tab.
 
------
ABS Juice: help with sticking to the bed (especially for large prints)
*when bed is cool, wipe the kapton tape clean with acetone (I used a paper towel with acetone on it)
*take a clean paper towel, put acetone on it and wipe a piece of the ABS with it to get some 'ABS juice' on the towel. Then wipe this over the bed. There should be some failed prints in the 3D printer, or check the mini-can beside the 3D printer for failed prints
*allow to dry completely (~5 minutes), you should see streaks of ABS on the bed. Heat up bed and print as usual.
*ABS should now stick well. Remember to block the build volume to stop air drafts.
------
 
It's better to start ABS prints towards the back of the printer where ambient temperature is more stable. To disable auto-centering, in Slic3r Prusa Edition go to File --> Preferences then uncheck 'Auto-center Parts'.
 
First Layer:
    Fillament: 240
    Bed:      100
    Bed for large prints: 120, use ABS juice!! (See above)   
 
 
Other Layers:
    Fillament: 235
    Bed:      95
    Bed for large prints: 110


==Octoprint at octopi4.hacklab.to==
==Octoprint at octopi4.hacklab.to==
Line 215: Line 196:


FlashForge Creator X, Pro & Dreamer Nozzle Height Adjustment -- https://www.youtube.com/watch?v=1pAPA0mImhI
FlashForge Creator X, Pro & Dreamer Nozzle Height Adjustment -- https://www.youtube.com/watch?v=1pAPA0mImhI
Belt tightening on X and Y axis - https://www.youtube.com/watch?v=fV4BFUdVx4U


== Maintenance Log ==
== Maintenance Log ==
Line 223: Line 206:
!Notes
!Notes
!Entry By
!Entry By
|-
| June 12, 2019
| Y-axis appeared to be skipping steps, but we found that there was a set screw loose on the timing pulley on one of the sides, so the whole gantry was driven by the belt on one side only. We tightened the set screw and squared the axis. Also, we flipped the timing belt pulley (hub toward the motor) on the Y axis motor so that the belt doesn't touch the motor flange. It's harder to access but it's tightened well and hopefully you won't have to tighten it again. We also retightened all the other belts for good measure. It works well now.
| Misha
|-
| May 2019
| The feeding tube for the filament is too wide (4 mm ID 6 mm OD) and too stiff as a result. The problem is, it pushes on the print head in one direction so when the axis is loose, it is printing skewed towers of pisa, in the direction in which the tube pushes. We fed the wire without the tube so that there is no extra pressure on the axis. Therefore the printing errors average to zero.
We bought a smaller and less springy tube (also PTFE) but we are waiting for someone more knowledgeable to install it.
| Misha
|-
| Jan 16, 2019
| Loosened the Y-axis short belt, lol. In my zeal I tightened it too much, I guess... (the prints were still drifting back a little, the vertical lines were wobbly...) The belt is good now I think, it should make a low sound when you strum the belt. Also changed the screws holding the Y-stepper, added washer and a rubber ring to keep it in place.
| Rana
|-
| Jan 11, 2019
| Tightened X belt, and the small Y belt that connects the motor to the cross rod. Cleaned and lubricated all rods (X, Y, Z). Lubricated Z lead screw. Lubricated the rod bearings on the X and Y (including that the bearings for the cross rod that connects to two Y long belts). Tightened the coupling on the Y axis stepper motor.
Prints were drifting (aka. leaning) towards the rear of the printer and it was driving me nuts. Turns out this can be due to a loose belt. The replicator and clones are susceptible the Y axis becoming loose because extra torque is outputted by the motor since it has to move the extruder carriage and the X stepper.
I also removed some cobwebs from under the printer electronics.
| Rana
|-
| Nov-Dec, 2018
| The aluminum print bed is warped (bowed, with middle as the high point). After trying to level it five million times, finally hit the printer with a baseball bat and it fixed it. Just kidding. Bought a GO 3D glass plate for the bed and a PEI sheet and a silicone heat transfer mat that keeps it in place.
| Rana
|-
| Aug 8, 2018
| Added Lokbuild surface to print bed. No more tape! see section above for usage info
| Rana
|-
|-


Line 283: Line 301:


|}
|}
[[Category:3D Printers]]
283

edits

Navigation menu