Laser Electronics

From Hacklab.TO Public Wiki
Revision as of 05:21, 9 March 2018 by Atrain (talk | contribs) (→‎Code: Updated source to assumed code)
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

Laser Cutter Electronics

File:Laser-control board.pdf

File:Laser-motor driver.pdf


Laser control board pinout

Left Header: (Top to Bottom)

  • GND (Shield)
  • SW_1 (Yellow)
  • SW_2 ( Green)
  • SW_4 (Blue)
  • SW_8 (Lt Purple)
  • Disable (Lt Brown)
  • ...

Top Header: (left to right)

  • Output to LEDs
  • PWM output to laser tube (2 pins - black, red)

Bottom Header: (Left to right)

  • Laser EN (Black)
  • ...
  • (I/O to parallel port here)

Right Header: (Top to bottom)

  • ...
  • (Power Input & output to stepper driver)

Laser Power controller board pinout

Long header:

  • yellow = switch input
  • blue = parallel input
  • green = output to PIC (where switches used to go)

Top header:

  • Pin 1 (Orange wire) LASER_EN
  • Pin 3,4 - (Purple) Mode Switch
  • Pin 5 - Ground
  • Pin 6 - 5V


Code

When we replaced the motor controllers back in 2016; we moved the step generation logic off the PIC, and replaced it with a single "MOTOR_EN" output instead.

The original code changes have not been found, so the following is assumed but unvalidated.


/*
 * Laser Engraver Controller - ver. 1.1a
 *
 * Written by: Andrew Kilpatrick
 * Copyright: 2009, 2016
 *
 * Runs on PIC16F877A
 *
 * Functional Description:
 *  - support for connection to emc2 or similar host-driven CNC software
 *  - parallel port or other type of bit-bang connection to PC
 *  - E-stop and system run control support (amp enable, charge pump, etc.)
 *  - controls laser PWM control
 *
 * Hardware I/O:
 *  - RA0    - laser power bit 0        - input - active high
 *  - RA1    - laser power bit 1        - input - active high
 *  - RA2    - laser power bit 2        - input - active high
 *  - RA3    - laser power bit 3        - input - active high
 *  - RA4    - laser defeat            - input - active high
 *
 *  - RB0    - E stop loop            - input - 0 = run, 1 = stop
 *  - RB3    - motor_enable            - output
 *  - RB4    - laser activate        - input - 0 = off, 1 = on
 *
 *  - RC0    - amp enable LED        - output - 0 = off, 1 = on
 *  - RC1    - laser LED            - output - 0 = off, 1 = on
 *  - RC2    - laser PWM            - output - 0 = off, 1 = on
 *
 *  - RE0    - E stop output            - output - 0 = stop, 1 = run
 *  - RE1    - amp enable input        - input - 0 = disable, 1 = enable
 *  - RE2    - charge pump input        - input - high pulses to charge
 *
 */
#include <system.h>

#pragma CLOCK_FREQ 20000000

#pragma DATA 0x2007, _CP_OFF & _DEBUG_OFF & _CPD_OFF & _LVP_OFF & _BODEN_ON & _HS_OSC & _WDT_ON & _PWRTE_ON

// inputs
#define LASER_POWER_1_IN porta.0
#define LASER_POWER_2_IN porta.1
#define LASER_POWER_4_IN porta.2
#define LASER_POWER_8_IN porta.3
#define LASER_DEFEAT_IN porta.4
#define E_STOP_IN portb.0
#define MOTOR_EN portb.3
#define LASER_IN portb.4
#define AMP_ENABLE_IN porte.1
#define CHARGE_PUMP_IN porte.2

// outputs
#define AMP_ENABLE_LED portc.0
#define LASER_ON_LED portc.1
#define E_STOP_OUT porte.0

// laser setting
#define LASER_TICKLE 0x01

// run state machine
#define STATE_IDLE 1
#define STATE_RUN 2
#define STATE_E_STOP 3
unsigned char run_state;

// globals
unsigned char run;                // 1 = normal, 0 = stopped
unsigned char charge_pump;        // 0 = stopped, >0 = run
unsigned char old_ch_pump;
unsigned char laser_init;        // 1 = laser initialized, 0 = not initialized
unsigned char laser_power;        // laser power level
unsigned char laser_on;            // 1 = laser on, 0 = laser off
unsigned char flash;            // temp flasher variable

// function prototypes
void step_laser(void);

// main loop
void main() {
    // set up IO
    porta = 0x00;
    trisa = 0xff;  // inputs
    adcon1 = 0x06;  // all digital pins
   
    portb = 0x00;
    trisb = 0xF7;  // inputs except for MOTOR_EN
    option_reg.NOT_RBPU = 0;  // weak pullups
   
    portc = 0x00;
    trisc = 0x00;  // outputs
    AMP_ENABLE_LED = 0;
    LASER_ON_LED = 0;
    ccpr1l = 0x00;
    ccp1con = 0x0c;  // PWM mode
    t2con = 0x05;  // prescaler 4, timer on
   
    trise.PSPMODE = 0;  // no data port
   
    porte = 0x00;
    trise &= 0xfe;  // RE0 = output, RE1-2 = input
    E_STOP_OUT = 1;  // no E stop

    t1con = 0x21;  // 1:4 prescaler, internal clock, timer on

    // reset temp vars
    run = 0;
    laser_init = 0;
    laser_on = 0;
    flash = 0;
    run_state = STATE_IDLE;
    charge_pump = 0;
    old_ch_pump = 0;

    // bootup light dance
    AMP_ENABLE_LED = 0;
    LASER_ON_LED = 1;
    delay_ms(250);
    delay_ms(250);
    AMP_ENABLE_LED = 1;
    LASER_ON_LED = 0;
    delay_ms(250);
    delay_ms(250);
    AMP_ENABLE_LED = 0;

    // loop
    while(1) {
        clear_wdt();
       
        // do stuff every 50ms
        if(pir1.TMR1IF) {
            pir1.TMR1IF = 0;
           
            // charge pump
            if(charge_pump) charge_pump --;
           
            // EMERGENCY STOP!
            if(E_STOP_IN) {           
                run_state = STATE_E_STOP;               
                E_STOP_OUT = 0;
               
                // turn off the laser
                ccpr1l = 0x00;  // power level to 0
                ccp1con &= 0xcf;  // power level to 0
                laser_power = 0;
                laser_on = 0;
                LASER_ON_LED = 0;
           
                // turn off motors
                MOTOR_EN=0;
                portc &= 0x0f;


                // LED flashing
                flash = (flash + 1) & 0x07;
                if(flash & 0x04) {
                    AMP_ENABLE_LED = 1;
                }
                else {
                    AMP_ENABLE_LED = 0;
                }
            }
            // E STOP cleared - enter idle state
            if(run_state == STATE_E_STOP && !E_STOP_IN) {
                run_state = STATE_IDLE;
                AMP_ENABLE_LED = 0;
                E_STOP_OUT = 1;
            }
            // amplifier enabled - enter run state
            if(run_state == STATE_IDLE && AMP_ENABLE_IN && charge_pump > 0x7f) {
                run_state = STATE_RUN;
                AMP_ENABLE_LED = 1;
                ccpr1l = LASER_TICKLE;  // make tickle puses for the laser
                ccp1con |= 0x30;  // PWM mode
                                //enable motors:
                                MOTOR_EN=1;

            }
            // amplifier disabled - enter idle state
            if(run_state == STATE_RUN && (!AMP_ENABLE_IN || charge_pump < 0x80)) {
                run_state = STATE_IDLE;
                AMP_ENABLE_LED = 0;

                // turn off the laser
                ccpr1l = 0x00;  // power level to 0
                ccp1con &= 0xcf;  // power level to 0
                laser_power = 0;
                laser_on = 0;
                LASER_ON_LED = 0;
           
                // turn off motors
                MOTOR_EN=0;
                portc &= 0x0f;
            }
           
            // handle laser power adjustments in run state
            if(run_state == STATE_RUN) {
                // laser power adjust
                if(LASER_DEFEAT_IN) {
                    // force laser into tickle
                    ccpr1l = LASER_TICKLE;
                    laser_power = 0;
                    LASER_ON_LED = 0;
                }
                else {
                    laser_power = (porta & 0x0f) << 4;
                    // if laser is on, change power immediately
                    if(laser_on) {
                        ccpr1l = laser_power;
                        LASER_ON_LED = 1;
                    }
                }
            }           
        }
       
        // handle charge pump on rising edge
        if(CHARGE_PUMP_IN && !old_ch_pump) {
            if(charge_pump != 0xff) charge_pump ++;
        }
        old_ch_pump = CHARGE_PUMP_IN;
    }
}

Tube

The tube on the laser cutter is a 25W Synrad F48-2S

Manual for that version does not appear online, but here are manuals for newer ones: