Ultimaker 2: Difference between revisions
Jump to navigation
Jump to search
m (→Features) |
(→Machine Log: 2 fixes) |
||
| Line 27: | Line 27: | ||
!Notes | !Notes | ||
!Entry By | !Entry By | ||
|- | |||
|March 9, 2017 | |||
|The Print Head Fan Duct was touching the build plate before the front/right corner was down enough to be level. Used a fine file to trim the underside of this 3D printed part, so this now stays just slightly above the build plate at all times. | |||
|Allen | |||
|- | |||
|March 1, 2017 | |||
|X axis just stopped working mid-print again. Re-seated x axis stepper board again, and this time used Kapton Tape to secure all the the stepper board DIPs in place. | |||
|Allen | |||
|- | |- | ||
|February 21, 2017 | |February 21, 2017 | ||
|Igor helped to locate & fix bad driver board (DIP socket) connections for the X axis stepper motor. Removed broken PLA from feeding tube (yet again). The working PLA reel from Ultimaker 1 was moved to this unit. | |Igor helped to locate & fix bad driver board (DIP socket) connections for the X axis stepper motor. Removed broken PLA from feeding tube (yet again). The working PLA reel from Ultimaker 1 was moved to this unit. | ||
|Allen | |Allen | ||
|- | |- | ||
Revision as of 23:56, 12 March 2017
This page documents Ultimaker #2 (Fawkes) [A phoenix from the ashes]
Printer lives on the third shelf of the 3D printer tower, next to the Type A.
Status
- Down ... not extruding filament out the print head
- Loaded with Turquoise 2.85mm PLA
- PLA ONLY! (to prevent nozzle contamination)
- Cura 15 Settings here
- http://octopi2.hacklab.to/
Features
- Ultimaker Original with extruder drive upgrade
- Built from an incomplete kit and a bunch of parts are 3D printed
- 210 x 210 x 205 mm print volume
- 2.85mm filament
- Absolute max temperature: 250 C
- It is managed and accessible from the web GUI: http://octopi2.hacklab.to/
Machine Log
| Date | Notes | Entry By |
|---|---|---|
| March 9, 2017 | The Print Head Fan Duct was touching the build plate before the front/right corner was down enough to be level. Used a fine file to trim the underside of this 3D printed part, so this now stays just slightly above the build plate at all times. | Allen |
| March 1, 2017 | X axis just stopped working mid-print again. Re-seated x axis stepper board again, and this time used Kapton Tape to secure all the the stepper board DIPs in place. | Allen |
| February 21, 2017 | Igor helped to locate & fix bad driver board (DIP socket) connections for the X axis stepper motor. Removed broken PLA from feeding tube (yet again). The working PLA reel from Ultimaker 1 was moved to this unit. | Allen |
| Mid-2016 | Re-printed extruder drive tensioner in ABS on Ultimaker 1, replaced Bowden tube coupler springs. Snipped 1cm off the tube ends to give couplers fresh surface to hold on to. | Igor |
| September 26, 2015 | Removed overly-brittle, broken PLA from the feeding tube. Machine back in working order with new PLA. PLA can become stale and brittle due to moisture absorption. | Justin |
| July 28, 2013 | Found new Arduino mega and installed marlin firmware via CURA. Checked all axis movements, checked thermocouple via external temperature sensors and finalized hot-end. Installed build platform. Removed raspberry pi. | Norm |
| July 27, 2013 | Cemented thermocouple into tube, fit tube into hot end. Attempted firmware uploads using Cura (failed) and Xloader (succeeded) | Norm |
| June 23, 2013 | Machined remaining parts and assembled feeder, mounted and tested (dry run without power, tensioner only). Attached flying lead ends of thermocouple onto thermocouple amp. |
Norm |
| June 22, 2013 | Printed out and assembled most of the feeder, lubricated gantry. | Norm |
| June 18, 2013 | Printed out parts for feeder | Norm |
| June 10, 2013 | Stripped apart old filament feeder and began building new feeder which uses the hobbed pulley. Parts on order, machined other parts. | Norm |
| June 8, 2013 | Rebuilt hot-end, rebuilt gantry components, mounted entire gantry, roughly aligned belts, verified general mechanical functions! Finished mounts for build platform (cutting build platform and mounting to be completed). |
Norm |
| May 29, 2013 | Boden tube, V2 hot end components, and belts arrived. | Norm |
| May 16, 2013 | Ordered Boden tube and V2 hot end components (the feeder upgrade can be printed for cheap). Belts ordered for Ultimaker 1 (when they are needed for replacement). (~$138) | Norm |
| May 15, 2013 | Printed Z home switch adjustment block and holder. Designed and printed parts for new build platform system. |
Norm |
| April 29, 2013 | Printed fourth X/Y bushing block and Raspberry Pi bracket | Norm |
| April 27, 2013 | Assembled 3/4 X/Y bushing blocks, 4th print failed mid-print. | Norm |
| April 24, 2013 | Unmounted dual extruder.
Stripped out X/Y gantry parts for rebuild (X/Y blocks broken). |
Norm |
| April 22, 2013 | Reorganized shelf to accommodate the Ultimaker, organized materials and supplies. | Norm |
To Do List
- Repairs
- Finish to-do list/upgrade list
- Reprint X/Y bushing blocks, remount
- Print tensioners, install
- Print new extruder in entirety, mount
- Print Raspberry Pi mounting plate, mount pi, wire up
- Straighten Z axis acme rod
- Crimp cable going to print head
- Remount X/Y gantry system
- Order hot end
- Order boden cable
- Order extruder (dependent on success of printable extruder)
- Flash firmware
- Calibrate endstops
- Printable Upgrades
- Spool holder
- Magnetically attached print bed
- Motor mounts
- Fan cowling
- Z axis home switch adjuster
- Axis end-caps