3D Printers/Ender 5 plus: Difference between revisions
(→Usage) |
(→Usage) |
||
| Line 59: | Line 59: | ||
- there is no octoprint or other network connection set up yet. There is usb port on the side of the touchscreen and there should be a usb stick in it, use that | - there is no octoprint or other network connection set up yet. There is usb port on the side of the touchscreen and there should be a usb stick in it, use that | ||
- use this config file for prusaslicer | |||
[[Media:Prusaslicer - ender 5 plus direct drive.zip]] | |||
- to load the filament push it all the way through the tubing to the direct drive extruder, then can use the "pickle rick" knob on the extruder to load it down to the nozzle | |||
- always check the first layer!!! there is live z-adjust on the touchscreen called "baby steps" | |||
== SD Card == | == SD Card == | ||
Revision as of 16:05, 5 December 2022
Status
Last Known Good Settings
| Date | Filament type, colour, brand | First layer | Other layers | Notes |
|---|---|---|---|---|
| June 28, 2020 | asdfsadfsdaf | asfsadfsadf |
Hardware
- screen is Big Tree Tech TFT35-E3 V3.0
- mainboard is Big Tree Tech SKR Mini E3 V2.0
- power supply is Mean Well RSP-500-24 (the good one, not first release of this printer that had a shitty one)
- Printhead is Micro Swiss Direct Drive and All-Metal Hot end
- Probe is official BL-Touch (which is stock on the E5P)
- it should be set and forget, don't think it needs to be recalibrated ever unless some hardware thing changes
- can use 'babystep' feature to live z-adjust during printing
- refer to this for setting the probe offset https://www.youtube.com/watch?v=y_1Kg45APko
Software
To use pronterface to control the printer, first power up the printer, then connect the usb cable to your computer. On win10 it should auto-detect and possibly install 'maple' (wtf that is lol). Baud 115200
Calibration notes
- using the built in e-steps I got 137.85 steps/mm (this is in the firmware, in the slicer you just change the flow rate)
Printable Upgrades
https://www.thingiverse.com/thing:4742487 https://www.thingiverse.com/thing:4742501
Voron cooling fans: https://www.thingiverse.com/thing:5171295
Z-axis sync indicators: https://www.thingiverse.com/thing:4460521
Glass Print Plate Usage
Usage
- there is no octoprint or other network connection set up yet. There is usb port on the side of the touchscreen and there should be a usb stick in it, use that - use this config file for prusaslicer Media:Prusaslicer - ender 5 plus direct drive.zip
- to load the filament push it all the way through the tubing to the direct drive extruder, then can use the "pickle rick" knob on the extruder to load it down to the nozzle - always check the first layer!!! there is live z-adjust on the touchscreen called "baby steps"
SD Card
Slicer Settings
* Using Cura, seems to be what most people are using
- flow settings are "hard-baked" into extrusion values in the gcode. So if you set flow to 95% in cura, there will NOT be an M221 S95 command in the gcode and so the printer will say on its screen that flow is 100%, but really the flow has been reduced.
A few random printing tips
know what you're doing!!! this printer is for seasoned vets only!!
Octoprint at octopi4.hacklab.to
I wish...
Maintenance Resources
put stuff here lol
Maintenance Log
Most recent entries at the top.
| Date | Notes | Entry By |
|---|---|---|
| June 9, 2022 | Setting up the printer | Rana |