Ultimaker 2
This page documents Ultimaker #2 (Fawkes) [A phoenix from the ashes]
Printer lives on the third shelf of the 3D printer tower, next to the Type A.
Status
- April 26th 2017, got great prints with the Bright Yellow PLA using these settings: 220C, speed 40 mm/s, flow 115%.
- Operational ... it can be Problematic
- Using a Brim to hold parts to the Print Bed is strongly recommended.
- Bed was leveled but Print Bed is NOT perfectly flat!
- Use 1/4 or 1/8 turn Z axis Zero Stop adjusts instead of trying to re-level the Print Bed.
- If head too close & extruder starts clicking, that can cause filament feed problems.
- Loaded with Bright Yellow 2.85mm PLA
- PLA ONLY! (to prevent nozzle contamination)
- Cura 15 Settings here
- http://octopi2.hacklab.to/
Features
- Ultimaker Original with extruder drive upgrade
- Built from an incomplete kit and a bunch of parts are 3D printed
- 210 x 210 x 205 mm print volume
- 2.85mm filament
- Absolute max temperature: 250 C
- It is managed and accessible from the web GUI: http://octopi2.hacklab.to/
Machine Log
| Date | Notes | Entry By |
|---|---|---|
| April 28, 2017 | Tightened all the frame screws. Unwittingly tightened the tensioner screw on the rails (the middle screw of those plastic pieces on the frame) and the head would not move. Loosened them and head moves good now.
The plastic connector for the printhead fan was coming in between the head and the orange rail holder, preventing homing. Secured that wire using a zip tie. |
Rana |
| April 26, 2017 | Filament was not extruding, took out the Bowden tube in the printhead and put it back in, it went several mm further in. Extruding fine now. | Rana |
| April 19-20, 2017 |
|
Allen |
| April 5, 2017 | Lubricate Y-Axis rods using NCR Silicone Fluid. Hardened/old lubricant on the Y-axis rods also removed by doing this. Using 30AWG wire to try cleaning print head. (Some dirt came out. Filament still curls towards head.) | Allen |
| March 9, 2017 | The Print Head Fan Duct was touching the build plate before the front/right corner was down enough to be level. Used a fine file to trim the underside of this 3D printed part, so this now stays just slightly above the build plate at all times. | Allen |
| March 1, 2017 | X axis just stopped working mid-print again. Re-seated x axis stepper board again, and this time used Kapton Tape to secure all the the stepper board DIPs in place. | Allen |
| February 28, 2017 | Lubricate X-Axis rods using NCR Silicone Fluid. X-Axis now moves back & forth smoothly. (Left side of belt no longer bends sideways @ the stepper motor.) Hardened/old lubricant on the X-axis rods also removed by doing this. | Allen |
| February 21, 2017 | Igor helped to locate & fix bad driver board (DIP socket) connections for the X axis stepper motor. Removed broken PLA from feeding tube (yet again). The working PLA reel from Ultimaker 1 was moved to this unit. | Allen |
| Mid-2016 | Re-printed extruder drive tensioner in ABS on Ultimaker 1, replaced Bowden tube coupler springs. Snipped 1cm off the tube ends to give couplers fresh surface to hold on to. | Igor |
| September 26, 2015 | Removed overly-brittle, broken PLA from the feeding tube. Machine back in working order with new PLA. PLA can become stale and brittle due to moisture absorption. | Justin |
| July 28, 2013 | Found new Arduino mega and installed marlin firmware via CURA. Checked all axis movements, checked thermocouple via external temperature sensors and finalized hot-end. Installed build platform. Removed raspberry pi. | Norm |
| July 27, 2013 | Cemented thermocouple into tube, fit tube into hot end. Attempted firmware uploads using Cura (failed) and Xloader (succeeded) | Norm |
| June 23, 2013 | Machined remaining parts and assembled feeder, mounted and tested (dry run without power, tensioner only). Attached flying lead ends of thermocouple onto thermocouple amp. |
Norm |
| June 22, 2013 | Printed out and assembled most of the feeder, lubricated gantry. | Norm |
| June 18, 2013 | Printed out parts for feeder | Norm |
| June 10, 2013 | Stripped apart old filament feeder and began building new feeder which uses the hobbed pulley. Parts on order, machined other parts. | Norm |
| June 8, 2013 | Rebuilt hot-end, rebuilt gantry components, mounted entire gantry, roughly aligned belts, verified general mechanical functions! Finished mounts for build platform (cutting build platform and mounting to be completed). |
Norm |
| May 29, 2013 | Boden tube, V2 hot end components, and belts arrived. | Norm |
| May 16, 2013 | Ordered Boden tube and V2 hot end components (the feeder upgrade can be printed for cheap). Belts ordered for Ultimaker 1 (when they are needed for replacement). (~$138) | Norm |
| May 15, 2013 | Printed Z home switch adjustment block and holder. Designed and printed parts for new build platform system. |
Norm |
| April 29, 2013 | Printed fourth X/Y bushing block and Raspberry Pi bracket | Norm |
| April 27, 2013 | Assembled 3/4 X/Y bushing blocks, 4th print failed mid-print. | Norm |
| April 24, 2013 | Unmounted dual extruder.
Stripped out X/Y gantry parts for rebuild (X/Y blocks broken). |
Norm |
| April 22, 2013 | Reorganized shelf to accommodate the Ultimaker, organized materials and supplies. | Norm |
To Do List
- Repairs
- Finish to-do list/upgrade list
- Reprint X/Y bushing blocks, remount
- Print tensioners, install
- Print new extruder in entirety, mount
- Print Raspberry Pi mounting plate, mount pi, wire up
- Straighten Z axis acme rod
- Crimp cable going to print head
- Remount X/Y gantry system
- Order hot end
- Order boden cable
- Order extruder (dependent on success of printable extruder)
- Flash firmware
- Calibrate endstops
- Printable Upgrades
- Spool holder
- Magnetically attached print bed
- Motor mounts
- Fan cowling
- Z axis home switch adjuster
- Axis end-caps