PCNC1100: Difference between revisions

Jump to navigation Jump to search

PCNC1100 (view source)

Revision as of 16:17, 6 March 2023

2,512 bytes added ,  6 March 2023
no edit summary
No edit summary
No edit summary
 
(2 intermediate revisions by the same user not shown)
Line 40: Line 40:
*NO OIL
*NO OIL
*Should be compatible with both ferrous metals and aluminum.
*Should be compatible with both ferrous metals and aluminum.
Recommended: "xtreme cut 250" from torontolube.ca
 
Currently selected coolant:
*Qualichem XTREME CUT 250C
*Source: torontolube.com, Alan at customerservice@torontolube.com - 1 gallon jug is all we need, which is below their minimum quantity - but they made an exception.
*Dilute to 8-10% by adding concentrate to tap water (not the other way around!)
See preventative maintenance
 
 


Good idea: [https://www.reddit.com/r/Machinists/comments/j5vjk1/diy_window_air_blast_for_cnc_lathe/]
Good idea: [https://www.reddit.com/r/Machinists/comments/j5vjk1/diy_window_air_blast_for_cnc_lathe/]
Line 69: Line 76:
**Check coolant level
**Check coolant level
**Remove chips from ways, carriage and bellows
**Remove chips from ways, carriage and bellows
**Agitate coolant with air (todo aquarium pump)
*Long-term
*Long-term
**Check coolant concentration; remove sediment
**Check coolant level and concentration; remove sediment
***Refractometer directly reads concentration for XTREME CUT 250C. 6-8% is OK.
**Skim coolant to remove oil regularly (oil grows bacteria)
**Check axes are receiving oil, check belts
**Check axes are receiving oil, check belts


Line 76: Line 86:
*Uses PathPilot (based on LinuxCNC)
*Uses PathPilot (based on LinuxCNC)
*TODO
*TODO
'''Insert Tooling'''
*Cutting conditions
**P - Steel
**M - Stainless Steel
**K - Cast Iron
**N - Nonferrous metal (e.g. aluminum)
**S - Exotic alloy
**H - Hardened steel


'''Tool Holder'''
'''Tool Holder'''
*TTS - Tormach Tooling System
*TTS - Tormach Tooling System
**The TTS adapts the R8 taper (same as the manual mill) in the spindle to a quick-change system
**Press RELEASE button above the spindle OR the foot pedal on the left side to insert or remove a TTS tool holder from the spindle.
*Tooling - our TTS set contains:
**ER16 collet - qty2
***Can hold 1/32" through 3/8" - but we have no ER16 collets
**ER20 collet - qty16
***We have 16 holders which can take ER20 collets - more than we have ER20 collets actually.
***These are ER20 collets which get snapped into the holder before being assembled:
***[[File:er20_collets.jpg]]
***Can accept ER20 collets which hold 1/16" through 1/2" or 1-13mm
***ER20 collets we have in stock: TODO
**Tormach SuperFly cutter [https://tormach.com/tts-superfly-cutter-kit-33031.html link] (2-3" adjustable cutting diameter, one cutter, $10 per insert + $200 of tool)
***SEHT12043AFSN (300-1000SFM For Steel - qty2 remaining
***SEHT1204AFTN (900-2360SFM) For Nonferrous - qty1 remaining
**Tormach Indexable face mill [https://tormach.com/face-mill-38mm-31280.html link] 1.5" dia, 4 cutters, $15 each = $60 of inserts + $200 of tool)
***APMT1135PDER (900-2360SFM 0.001-0.005"/rev) For Steel  - qty6 remaining
***APKT113508PDFR  (900-2360SFM 0.0012-0.0059"/rev) For Nonferrous  - qty4 remaining
**1/4" set screw - qty11
**5/16" set screw - qty2
**3/8" set screw - qty10
**1/2" set screw - qty5
***We have replacement for TTS set screws (per NYC CNC for this machine): 
****McMaster p/n 92311A556 (1/4x28 Stainless Set Screw). 
****McMaster p/n McMaster 92311A635 (3/8x24 Stainless Set Screw). 
**Jacobs chuck JT2 - qty4
**Jacobs chuck 1/32-3/8" - qty1
**Jacobs chuck 1/64-1/4" - qty1
**Collet 5C expanding #4 (to hold *inside* a bore) - qty1
**Blank (make your own tool or mount magnetic base [https://tormach.com/tts-machinable-blank-31802.html link]) - qty2
**Tormach active 3D probe - $1800
***Replacement tips $120 [https://tormach.com/replacement-probe-tip-31899.html link]
*Total value of TTS tooling is over $4000


'''Items to purchase'''


'''Flood Coolant'''
Qualichem XTREME CUT 250C
Source: torontolube.com, Alan at customerservice@torontolube.com - 1 gallon jug is all we need, which is below their minimum quantity - but they made an exception.
Dilute to 8-10% by adding concentrate to tap water (not the other way around!)
Measure with refractometer and add water regularly to compensate for evaporation
Skim to remove oil regularly (oil grows bacteria)
Agitate with air regularly (todo aquarium pump)
'''Items to purchase'''
*Replacement for TTS set screws (per NYC CNC for this machine):  McMaster p/n 92311A556 (1/4x28 Stainless Set Screw).  Larger Tormach Set Screw holders use 3/8x24 (McMaster 92311A635)
*[https://www.nyccnc.com/buy-tormach-pcnc-1100-cnc-mill/| NYC CNC "What to buy for Tormach PCNC1100" (this machine)]
*[https://www.nyccnc.com/buy-tormach-pcnc-1100-cnc-mill/| NYC CNC "What to buy for Tormach PCNC1100" (this machine)]
*Coolant (IN PROGRESS - WG)
*Busy bee 10mm clamp kit (IN PROGRESS - WG)
*Busy bee 10mm clamp kit (IN PROGRESS - WG)
*Aquarium air pump for coolant, to run a few hours a day


Sources:
Sources:
Line 103: Line 143:
[https://www.nyccnc.com/speeds-feeds-excel-worksheet/| NYC CNC Speeds and Feeds worksheet]
[https://www.nyccnc.com/speeds-feeds-excel-worksheet/| NYC CNC Speeds and Feeds worksheet]
[https://www.nyccnc.com/speeds_feeds/tormach-speeds-feeds/| NYC CNC Speeds and Feeds Videos]
[https://www.nyccnc.com/speeds_feeds/tormach-speeds-feeds/| NYC CNC Speeds and Feeds Videos]
{| class=wikitable
|+ Tool Table
! Tool#
! Shape
! Diameter
! Length
! Part number
! Price
|-
! T60 || 2fl cobalt Endmill || 0.375? || ? || KBC 1-329-024 || $24
|-
! T61 || 2fl cobalt Ball|| 0.125? || ? || KBC 1-325B-008 || $12
|-
! T62 || 3fl Hog endmill for Aluminum ONLY || .375? || ? || KBC 5-100-13417 || $115
|}


{| class=wikitable
{| class=wikitable
Line 110: Line 167:
! SFM with Flood Coolant
! SFM with Flood Coolant
|-
|-
! 6061 Aluminum + 1/2" HSS endmill
! 6061 Aluminum + 3/8" cobalt endmill - roughing facing|| N/A || 50% stepover 25IPM 0.1"DOC pretty good, but so did 200% stepover. Forgiving.
| Cell 2 || Cell 3
|-
|-
! Row header A
! 6061 Aluminum + 3/8" cobalt endmill - roughing profile || N/A || .05" stepover 25IPM 0.6"DOC pretty good
| Cell B
|-
| Cell C
! 6061 Aluminum + 1/8" cobalt endmill - finishing profile || N/A || .002" stepover 5IPM 0.3"DOC climb looks great
 
|}
|}
Retrieved from "https://knowledge.hacklab.to/wiki/Special:MobileDiff/1934...2099"

Navigation menu