Type A: Difference between revisions
Jump to navigation
Jump to search
Retired Printer
(→Machine Log: update for work done) |
(Retired Printer) |
||
| (5 intermediate revisions by one other user not shown) | |||
| Line 8: | Line 8: | ||
* '''Operational''' ... use PETG head '''only''' for PETG, and the PLA head '''only''' for PLA. | * '''Operational''' ... use PETG head '''only''' for PETG, and the PLA head '''only''' for PLA. | ||
** PETG printhead in printer -- loaded with 1.75mm Blue iPrint-3D PETG. | ** PETG printhead in printer -- loaded with 1.75mm Blue iPrint-3D PETG. | ||
* The Buld Plate is no longer perfectly flat. (Small high area, centered on X-axis & bit behind Y-axis center.) | |||
* The Printhead Heatsink Fan is '''always on''' ... so don't leave this printer powered on for long periods of time without printing. | * The Printhead Heatsink Fan is '''always on''' ... so don't leave this printer powered on for long periods of time without printing. | ||
* [[3D_Printers#Cura_15|Cura 15 Settings here]] (see Cura 3 Settings section instead.) | * [[3D_Printers#Cura_15|Cura 15 Settings here]] (see Cura 3 Settings section instead.) | ||
| Line 64: | Line 65: | ||
'''Quality''' | '''Quality''' | ||
* Layer Height: 0.225 mm (Using "Adaptive Layers", so this really means from 0.175mm to 0.275mm) | * Layer Height: 0.225 mm (Using "Adaptive Layers", so this really means from 0.175mm to 0.275mm)<br />==> Using a Layer Height more than 2.75mm or less than 1.75mm seems to cause a LOT more PETG build-up on the outside of the nozzle. | ||
* Initial Layer Height: 0.3 mm | * Initial Layer Height: 0.3 mm | ||
* Line Width: 0.35 mm ('''smaller''' than the 0.4mm nozzle) | * Line Width: 0.35 mm ('''smaller''' than the 0.4mm nozzle) | ||
| Line 223: | Line 224: | ||
!Notes | !Notes | ||
!Entry By | !Entry By | ||
|- | |||
| June 28, 2020 | |||
| | |||
* This Machine has been retired, it was taken home during the HL2 => HL3 by a member. This was with the consent of the hacklab membership. | |||
| Revident | |||
|- | |- | ||
| Line 575: | Line 583: | ||
==Parts and Supplies Wish List== | ==Parts and Supplies Wish List== | ||
* Connector Parts needed to finish other 2 Printheads -- and also to try different filament cooling fans. | |||
** 3 pieces of: https://www.digikey.ca/products/en?keywords=Wm1845-ND (Have 2 of these.) | |||
** 20 pieces of: https://www.digikey.ca/products/en?keywords=Wm1837CT-ND (Have 4 of these.) | |||
** 8 pieces of: https://www.digikey.ca/products/en?keywords=Wm1855-ND (Have 2 of these. Also for cooling fan.) | |||
** 50 pieces of: https://www.digikey.ca/products/en?keywords=Wm1841CT-ND (Have NONE of these. Also for cooling fan.) | |||
PLEASE NOTE: These connectors are '''extremely difficult''' to crimp in a manner they work. So at least '''double''' the crimp-connector parts are needed to get solid/working connectors. | |||
*www.aliexpress.com/item/A-Funssor-Silicone-Socks-for-v6-hotend-SILICONE-HEATER-BLOCK-COVER-Heater-Block-Silicone-Insulation-Blue/32823079702.html | *www.aliexpress.com/item/A-Funssor-Silicone-Socks-for-v6-hotend-SILICONE-HEATER-BLOCK-COVER-Heater-Block-Silicone-Insulation-Blue/32823079702.html | ||