Search results

* It's SD card reader has a broken latch. You have to use the octoprint web inte ...CR10. It's sd-card reader is busted, so this seemed the easiest way to get it up and running again. ...

It's a [http://www2.tek.com/cmswpt/psdetails.lotr?ct=PS&cs=psu&ci=13295&lc=EN It comes with some accessories that should remain with the scope at all times: ...

...barrel jack cable, so I cannibalised a USB-A to micro-B cable and soldered it directly to the board. ...MI2. The Wii U is connected to it as Input 1. The Xbox 360 is connected to it as Input 2. ...

To meet needs at the time, this has had it's software replaced with OpenWRT. The CloudKey (HL0029) and this unit could [[Category:IT]] ...

...ll-a-Watt was donated by Eric Boyd. Alaina is currently hacking it to turn it into a wifi-enabled power monitoring and switching device. (2011-04-07) ...

* It uses an ESP32-CAM running [https://github.com/jomjol/AI-on-the-edge-device ...tant access for utility company inspection/service, but is keyed such that it will re-align and (hopefully) not require software recalibration. ...

The Hacklab now has a small bench power supply! It is based on LM78xx regulators. It has +5V, +12V and a variable output (1.2V to 16V). The variable output ha ...

...use, please make sure to return it where it belongs when you're done with it, and contact sen (darkroom steward) if you have any questions! ** Has a few film holders and a 210mm lens with it ...

Using the boring bar! It's worth noting that Titanium CAN catch fire in a lathe!! Thus, it's essential to keep things cool with the coolant and to clear the titanium ...

No drivers should be required, plug into USB and it shows up as two sound devices, Speaker and Microphone. ...by Y6 on first floor) when not in use. There is a soft protective case for it. ...

This is a printer. It should just be available on the network. However demons may be involved. If you send a print job and it doesn't print, you may have to wake the printer up ("Energy Saver" button o ...

...twork, whatever. The equipment should also be yours to give -- make sure it is not on your employer's books. Loaned equipment should be CLEARLY LABED ...y well documented, in excellent condition, and is modern and interesting. It should be open, and software/firmware if required should be included or be ...

Its a sodastream! Get hacky with it and make some silly sodas. ...

It makes coffee, and is currently in need of a new gasket. ...

...the ultimakers, running the same Marlin firmware. This means you can treat it almost identially. (eg: Use Cura/tegh) ...uder. Note that it overshoots, raise the temperature slowly, and don't set it above 85C. ...

It has been copied over to the Public Wiki, and this iteration can be safely r ...through experimentation over a year of tweaking. This is the final result; it is smoky, spicy, and piquant. ...

...of all the printer's vital signs (temperatures, print jobs, you name it - it has [or should have] an event). ...ay) to make the printers discoverable to users and devices on the network. It's my (Rob) hope that a UDP API will be added to HTML5 in the future since r ...

# Attach the hose to the smaller white tube and screw it onto one of the tempered water taps. # Drop your film in and wait while it's washed! ...

==this page is outdated, i'm in the process of updating it. -- Dan == ...ce the blue heated build platform onto the area underneath the print head. It attaches with magnets and only goes on one way. Be careful to route the wi ...

;'''Q:''' Why does the card say 2021 on it? :'''A:''' Hacky New Years really only got it's name in 2022 targeting the 2023 new year. This project was retroactively ...