Ultimaker 1: Difference between revisions
Jump to navigation
Jump to search
Retired Printer
(Retired Printer) |
|||
| (14 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
[[File:Ultimaker 1.jpg|thumb|300px|Ultimaker #1, also known as "Guy"]] | [[File:Ultimaker 1.jpg|thumb|300px|Ultimaker #1, also known as "Guy"]] | ||
This page documents Ultimaker #1 (Guy). | This page documents Ultimaker #1 (Guy). | ||
Printer lives on the second shelf of the 3D printer tower, below the [[FlashForge Creator Pro]]. | |||
==Status== | ==Status== | ||
<onlyinclude> | <onlyinclude> | ||
* | * DOWN! ... has a '''serious''' head jam, which will need cold pulls to clear/fix. | ||
* '''Last known good settings:''' 220°, 110% flow, print 60mm/s, travel 120mm/s, 0.4 mm nozzle size, 2.85mm filament size. | * '''Last known good settings:''' 220°, 110% flow, print 60mm/s, travel 120mm/s, retraction 4.5mm @ 40mm/s, 0.4 mm nozzle size, 2.85mm filament size. | ||
* | * Silver PLA (from M G Chemicals) | ||
* Works well using Blue painter’s tape '''without''' using the heated bed. (Same setup as Ultimaker 2) | * Works well using Blue painter’s tape '''without''' using the heated bed. (Same setup as Ultimaker 2) | ||
* [[3D_Printers#Cura_15|Cura 15 Settings here]] | * [[3D_Printers#Cura_15|Cura 15 Settings here]] | ||
* '''http://octopi.hacklab.to/'''</onlyinclude> | * '''http://octopi.in.hacklab.to/'''</onlyinclude> | ||
==Known Issues and Fixes== | ==Known Issues and Fixes== | ||
* '''IMPORTANT:''' OctoPrint will '''disconnect from Ultimaker 2''' if Ultimaker 1 is powered on. If you want to print on both (or will want to eventually), power both on before starting your print on Ultimaker 2 | * '''IMPORTANT:''' OctoPrint will '''disconnect from Ultimaker 2''' if Ultimaker 1 is powered on. If you want to print on both (or will want to eventually), power both on before starting your print on Ultimaker 2 | ||
* Recommended CURA '''Retraction Settings:''' 4.5mm at 40mm/s | |||
* For better results, wipe the Blue Tape Sheet with Isopropyl Alcohol a few minutes before starting to print. | * For better results, wipe the Blue Tape Sheet with Isopropyl Alcohol a few minutes before starting to print. | ||
* '''If a large solid area is under-extruding''' then try printing PLA at 220° and 110% Flow. | * '''If a large solid area is under-extruding''' then try printing PLA at 220° and 110% Flow. | ||
== Features == | == Features == | ||
| Line 35: | Line 36: | ||
|- | |- | ||
|June 28, 2018 | | June 28, 2020 | ||
| | |||
* This Machine has been retired, replaced by Prusa Mini #1 | |||
| Revident | |||
|- | |||
|September 6, 2018 | |||
| | |||
* "Pipe on back" filament holder replaced by this filament holder on the shelf behind: | |||
https://www.thingiverse.com/thing:3002741 ... used file SpoolRollerL.stl to make this. | |||
* Bed Level was adjusted. | |||
| Allen | |||
|- | |||
|June 22, 2018 | |||
| | | | ||
* The New (Ultimaker original) Nozzle from Ultimaker 2 was swapped out, to put it on this machine. | * The New (Ultimaker original) Nozzle from Ultimaker 2 was swapped out, to put it on this machine. | ||
* Bed Level was checked, and Zero Stop was | * Bed Level was checked, and Zero Stop was adjusted. | ||
| Rana & Hiker ??? | | Rana & Hiker ??? | ||
|- | |- | ||
| Line 224: | Line 239: | ||
|} | |} | ||
==Parts and Supplies Wish List== | |||
* Hardened Nozzle for printing Carbon Fiber and '''any other''' Filled Filaments (including glow-in-dark). | |||
** A usable Hardened Nozzle from Canada: https://shop3d.ca/products/0-50mm-jet-steel-nozzle-for-olsson-block-rss50 ... $29.38 w/ shipping & tax | |||
*** '''See notes''' about using this nozzle with an UMO here: https://thegr5store.com/store/index.php/um2/rss50.html | |||
** Another possible Hardened Nozzle from Canada: https://spool3d.ca/nozzle-a2-reprap-m6-thread-3mm-filament-ultimaker-2-e3d-olsson-block/ ... $33.38 w/ shipping & tax (No Tracking!) | |||
[[Category:3D Printers]] | [[Category:3D Printers]] | ||