Search results
Jump to navigation
Jump to search
- # Turn on the flow of water so that the film washer fills up within 10-15 seconds. ...1 KB (193 words) - 07:19, 16 January 2019
- * The Card is done up as a 90s era PC BIOS boot sequence that then loads to a UNIX link operating ...2 KB (235 words) - 21:52, 29 January 2023
- # Sweep / vacuum up chips and leave the machine clean. ...1 KB (178 words) - 07:18, 16 January 2019
- # Sweep / vacuum up chips and leave the machine clean. * New front cover to replace the chewed up one ...3 KB (536 words) - 16:20, 30 October 2023
- * there is no octoprint or other network connection set up yet. There is usb port on the side of the touchscreen and there should be a ...st set the top and solid infill to 5 or more layers to make sure it covers up any drooping of the top layers ...6 KB (1,064 words) - 23:23, 26 February 2024
- A compilation of recipes that our members have come up with, or otherwise decided that should be shared among the membership. ...1 KB (219 words) - 21:58, 24 January 2019
- * Significant build of up plastic in extruder pulley teeth. Scrapped it out with a dental pick. ...1 KB (212 words) - 23:20, 26 February 2024
- * The spindle motor can be manually moved up/down to accommodate larger/smaller work # Sweep / vacuum up chips and leave the machine clean. ...5 KB (819 words) - 15:28, 7 March 2020
- ==== Installing and setting up PrusaSlicer ==== To set up PrusaSlicer to work with the HackLab PrusaMinis (and avoid the risk of sele ...9 KB (1,462 words) - 05:30, 3 March 2024
- ...oir, with the pumps controlled by the Arduino and 1Sheeld. We can then set up a placard telling people how to "give the plants some love" by installing t All are located in a bulk barn bag, which I have put back up in the storage area above the DIYBio area for now, though if we get started ...4 KB (760 words) - 07:17, 16 January 2019
- This write up covers Hacklabs various sewing machines. There are many like it but these o ...ft/separate tension plates from thread if needed; pull lower looper thread up - GENTLY! If the L lower looper thread breaks it is a total bitch to rethre ...4 KB (735 words) - 03:36, 2 February 2023
- ====Set-up and general==== The lathe has a tendency to make a decent mess. Please do your best to clean up the area around the lathe after you are done using it. This includes: ...8 KB (1,388 words) - 18:04, 29 March 2022
- ** Barcodes can be found on instruction sheets for each process that are hung up behind the door. ...2 KB (298 words) - 07:20, 16 January 2019
- # Sweep / vacuum up chips and leave the machine clean. * The fine adjust handwheel on the quill is not as accurate as the knee for up/down motion. Lock the quill before milling and use the knee to plunge into ...7 KB (1,108 words) - 15:37, 23 July 2019
- ** Use up/down arrows to scroll through the menus. You may need to press enter to lea *In the Lab Ops bin, you will find a hacked-up DSL filter which is a RJ11 to RS232 adapter, which you connect to the RJ11 ...4 KB (735 words) - 02:31, 22 February 2017
- # Do not sand on same spot on disk/belt, move around to reduce heat build-up and wear. # Sweep / vacuum up chips and leave the machine clean. ...4 KB (755 words) - 07:27, 16 January 2019
- ...ional when filling out the form, if left out then two people have to speak up on the list saying they've met them and approve before they're accepted as ...2 KB (328 words) - 19:14, 1 May 2016
- * Early 2015: Picked up bag of stuff from Creatron ...3 KB (434 words) - 07:19, 16 January 2019
- ...p the throat. Kept poking and removing molten plastic, then finally pushed up on the blocking piece and pushed it through to the bowden tube, which I the ...I've done as much troubleshooting as I can without risking screwing stuff up. I've sent a query to the mailing list. ...11 KB (1,684 words) - 02:39, 1 July 2020
- * Garbage bin emptied / garbage picked up ...2 KB (338 words) - 00:21, 20 January 2019