Search results

# Turn on the flow of water so that the film washer fills up within 10-15 seconds. ...

* The Card is done up as a 90s era PC BIOS boot sequence that then loads to a UNIX link operating ...

# Sweep / vacuum up chips and leave the machine clean. ...

# Sweep / vacuum up chips and leave the machine clean. * New front cover to replace the chewed up one ...

* there is no octoprint or other network connection set up yet. There is usb port on the side of the touchscreen and there should be a ...st set the top and solid infill to 5 or more layers to make sure it covers up any drooping of the top layers ...

A compilation of recipes that our members have come up with, or otherwise decided that should be shared among the membership. ...

* Significant build of up plastic in extruder pulley teeth. Scrapped it out with a dental pick. ...

* The spindle motor can be manually moved up/down to accommodate larger/smaller work # Sweep / vacuum up chips and leave the machine clean. ...

==== Installing and setting up PrusaSlicer ==== To set up PrusaSlicer to work with the HackLab PrusaMinis (and avoid the risk of sele ...

...oir, with the pumps controlled by the Arduino and 1Sheeld. We can then set up a placard telling people how to "give the plants some love" by installing t All are located in a bulk barn bag, which I have put back up in the storage area above the DIYBio area for now, though if we get started ...

This write up covers Hacklabs various sewing machines. There are many like it but these o ...ft/separate tension plates from thread if needed; pull lower looper thread up - GENTLY! If the L lower looper thread breaks it is a total bitch to rethre ...

====Set-up and general==== The lathe has a tendency to make a decent mess. Please do your best to clean up the area around the lathe after you are done using it. This includes: ...

** Barcodes can be found on instruction sheets for each process that are hung up behind the door. ...

# Sweep / vacuum up chips and leave the machine clean. * The fine adjust handwheel on the quill is not as accurate as the knee for up/down motion. Lock the quill before milling and use the knee to plunge into ...

** Use up/down arrows to scroll through the menus. You may need to press enter to lea *In the Lab Ops bin, you will find a hacked-up DSL filter which is a RJ11 to RS232 adapter, which you connect to the RJ11 ...

# Do not sand on same spot on disk/belt, move around to reduce heat build-up and wear. # Sweep / vacuum up chips and leave the machine clean. ...

...ional when filling out the form, if left out then two people have to speak up on the list saying they've met them and approve before they're accepted as ...

* Early 2015: Picked up bag of stuff from Creatron ...

...p the throat. Kept poking and removing molten plastic, then finally pushed up on the blocking piece and pushed it through to the bowden tube, which I the ...I've done as much troubleshooting as I can without risking screwing stuff up. I've sent a query to the mailing list. ...

* Garbage bin emptied / garbage picked up ...

* Make sure your contact info is up to date on https://booking.in.hacklab.to/selfservice/?action=info ...

...ve existing Events or Traditions that fit well or are convenient to double up with OMM. Go for it! OMM is about explicitly inviting / giving excuse for s ...

...members only Wifi or plugging into an ethernet cable. We are hoping to set up a virtual private network (VPN) in Hacklab 3.0. In the meantime, you can ss ...

...s ( SKR board, etc.) But was abandoned when 4 new creality printers showed up unexpectedly. Given the quality and constraints of this printer, there is n 4. increase print scale by 4.1353% (because something screws the scale up in this workflow) ...

...' structure (just outside the bed level screws), then gently move one side up, while the other moves down, to get the bed level. (Bed seems to stay level ...t cutting) takes HOURS to get the bed leveled. (Front left spring can't go up more. Back right level screw seems jammed.) ...

**** Consume messages from '''''hacktouch.audio.request''''' queue for volume up/down, mute, play, stop, etc. ...

...more than 2.75mm or less than 1.75mm seems to cause a LOT more PETG build-up on the outside of the nozzle. ...UNSELECTED<br />==> Limiting sudden movement changes permits PETG to build up on outside of head.<br /> ...

.../G-code G-code] files. G-code is not very standardized, so you should read up on the [http://www.linuxcnc.org/docview/html//gcode.html specific variety o ...er job starts in AXIS, it executes the 'M102' g-code command, which is set up to launch the Graster Streamer. The g-code itself just tells the laser hea ...

*Hansa Condenser Enlarger (up to 6×7) ...

# Sweep / vacuum up chips and leave the machine clean. ...

...an-lime-dessert/ Postre de Limon] for dessert as we're still trying to use up all the limes ....com/vegan-red-velvet-cake/ vegan red velvet cake] for dessert. Soup ended up being too salty as I lost track of the amount of salt. As for the cake, add ...

// set up IO ...